#CAR WAX BY HAND FREE#
This makes sure that the car paint is free of any fatty residue, left over polishing compound, or anything else. It is important to wipe the car before applying the wax. Step Four: Wipe The Car With Isopropyl Alcohol And Water It removes any dirt that might have settled on the car’s surface after washing and claying. The detail spray helps remove the soapy water used before the surface was clayed. Once the surface is free of contaminants, spray the clayed surface with detail spray and wipe it off using a microfiber cloth or towel. Step Three: Apply Detail Spray On The Surface If you encounter resistance on a particular part of the surface, glide the bar a few more times on the spot until the contaminant is successfully removed. Then, slide the clay bar on the surface using light pressure to help eliminate the contaminants. The contaminants may lead to scratching the paintwork when applying the wax, hence the need to eliminate them.ĭissolve a few drops of detergent in a water bottle, put it in a spray bottle, and spray the contents on the car’s surface to act as a lubricant for the clay bar to glide on easily. This step involves using a clay bar to remove any contaminants left on the car even after being washed. Wash the car, dry it off with a microfiber towel, and park it in a cool shade away from direct sunlight. Like in hand waxing, using a buffer to apply wax also needs the car to be fully clean before starting the process. The following steps should be followed when using the machine to apply wax on vehicles: Step One: Clean The Car You need the same materials as the hand waxing method, only that a machine is used this time instead of doing it by hand. Waxing a car with a buffer is much faster than waxing by hand, but it is much more complicated. Waxing A Car With A Buffer – Step By Step Instructions Use vertical motions when buffing in the wax, and the process is deemed complete. Use a microfiber towel or cloth to buff the waxed vehicle’s exterior to a smooth finish. When the wax application is complete, the next step is to make the car’s surface smooth and shiny.
Therefore, hastily slathering the wax all over the car at once without any structure shortens the application time but makes it harder to polish the vehicle and achieve a flawless finish. Car waxing by hand is time-consuming and takes a lot of hard work. Take your time when applying car wax by hand. This hack is helpful because mistakes are prevented early on rather than applying to the whole surface and noticing them later on when the damage is already done. Working in sections helps identify and correct hand waxing mistakes when the wax is being applied. Use the applicator pad to spread the wax in each section in a vertical motion.Īvoid circular motions when applying because they could leave behind swirl marks on the car, ruining the smooth finish intended. The final step is applying the wax, and good quality wax is paramount for excellent results.Īpply thin coats as you go, as too much wax is harder to apply and even out on the vehicle’s surface.Īlso, work in small sections and check each section before moving to the next one. So make sure to wipe your car with a mix of alcohol and water before applying the car wax. The better the bond, the longer the wax lasts and the better the protection is. Wiping the car with an alcohol-water mix makes sure that all fats and all left over polishing compound is properly removed.Īfter the wipe the paint will be “naked” and this allows the wax to bond perfectly with the paint. Remove the compound by polishing it with a microfiber towel.īe gentle with the polishing to avoid scratching the car with any dirt or dust that may have settled on the car while prepping it for waxing.
The compound is intended to help remove scratches and surface layers the clay bar couldn’t remove.ĭon’t overload the applicator pad with the agent, as it may leave white powder remnants in the cracks of the car. Use an applicator pad to apply the compounding agent in small amounts. With a smooth and clean surface, the next step is compounding the car by hand. Using plenty of lubricant helps avoid scratching the car’s surface when rubbing the clay bar on it. The lubricant helps the clay bar glide on the car’s surface easily to remove the contaminants, making it smooth.
0 kommentar(er)
